Myweigh DuraScale User Manual download pdf

DuraScale Manual & Advanced Programming

"I tried using my scale for the first time yesterday. The display would only show the A.ch.Er error. Pulling

up on the tray as described in the user manual's A.ch.Er User Repair section provided no change. I was

able to locate the "For advanced user repair of Durascale 100 V2 ONLY" section on your website. I was

unsure of my scale's version but decided to give these instructions a try. Everything appears to function

properly since. I simply wanted to thank you for providing the necessary information on your website. I

certainly appreciate it. David B. "

Low Batteries & bad battery connections are the #1 cause of scale malfunction and inaccuracy! We

test all of our scale returns from consumers. Fully 60% of consumer returns are battery related

problems. This sounds silly but it's true! A scale will perform slowly, or read inaccurately when it has low

batteries.Please replace the batteries often (and only use good qualitybatteries). We include good

quality batteries with all of our scalesbut batteries can run low in storage. If your scale simply won't turn

on while on Battery power, this is often caused by loose battery connections. Battery prongs (terminals)

are made of metal. They must be making good contact with your batteries in order for the scale to

power on. You can use a paperclip to slightly bend the battery prongs to make them have a better

connection. Also some poorly designed batteries have recessed or partially obstructed battery

terminals. This may cause your prongs to be touching the plastic housing of the battery instead of the

metal battery terminal.

Thank you for purchasing The DuraScale 100 or 50. With normal care and proper treatment it will

provide years of reliable service. Please read all operating instructions carefully. Although this manual

was current at the time of printing, we often update our user manuals and provide operation tips and

guidance on our website.

* Description of error codes that may show on the display:

‘50.00 g’ ----- max processing weight is 50g; ‘0

————

’----- zero-point is too large;

‘100.00 g’ ----- max processing weight is 100g; ‘0

————

’----- zero-point is too large;

‘A.oFF.x’----- auto-off time is ‘x’ minutes; ‘CAL-0 ’ ----- zero-point calibration;

‘CAL-F ’ ----- full range calibration; ‘A.ch.E r’ ----- there is an error in analog channel; Please try

recalibration, if this does not work please see at the bottom of this page for more instructions.

‘

—————

’ ------ the weight is over 50.09g/100.09g; ‘______’------ the weight is below -0.09g.

‘EEP.Er’ ----- there is an error in accessing eeprom;

‘Hld.on’/‘Hld.oF’ ----- display data holding function is available or disabled

‘Cnt.Er’ ----- the unit weight (the weight of one part) is less 1d; (in counting function)

1 2 3 4 5 6 7 8 9

Summary of Contents

Page 1

DuraScale Manual & Advanced Programming "I tried using my scale for the first time yesterday. The display would only show the A.ch.Er error.

Page 2

‘Cnt.xx’ ----- calculate unit weight using xx’s sample parts weight * NOTE: errors "‘0———— ’, ‘ —————’,‘______’ can usually be fixed by recalibra

Page 3

When first turning the unit on, the segments of the display will appear as shown below. This display will remain for approximately 5 seconds and then

Page 4

2) Press ‘TARE’, the ‘0’ in ‘CAL-0’ will flash; 3) When ‘CAL-F’ shows on the display, Place the 50gram calibration weight on the weighing platform 4

Page 5

6) Press ‘TARE’ , the ‘0’ in ‘CAL-0’ will flash When the calibration is finished, the scale will automatically turn off/reset NOTE: if after calibrati

Page 6

This advanced scale is equipped with a display lock setting to be used when you wish to keep a displayed value on the display. This works well when co

Page 7

6) When ‘xx pc’ is displayed (small pc in the upper part of the display, for example, ‘20 pc') is displayed, the scale is in parts counting mode,

Page 8

If you are unable to get your scale working normally again, please follow the warranty instructions that came with your Durascale to obtain a free rep

Page 9

perfect accuracy. Incorrect calibration can occur if you do not follow the steps exactly. You will need a 50g weight (DURA 50) /100g weight (DURA 100)

Comments to this Manuals

No comments

Myweigh DuraScale User Manual

Browse online or download User Manual for Scales Myweigh DuraScale. MyWeigh DuraScale User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Scales Myweigh DuraScale